This is the Grade 12 Mechanical Technology written in the May/June 2018 exams (Term 2). The paper counts 200 marks and learners had 3 hours to finish it. It has 10 questions covering terminology, forces, joining methods, systems and control, multiple-choice questions, turbines, maintenance, materials, tools and equipment and safety. Below you can download the question paper (Afrikaans), question paper (English), memo (Afrikaans) and memo (English) as free PDFs, then mark your answers with the memo.
Download the Term 2 May/June 2018 PDFs
-
Mechanical Technology Grade 12 Term 2 May/June 2018 Question Paper (Afrikaans)
Download the mechanical technology grade 12 june 2018 question paper PDF in Afrikaans. A real May/June exam paper to practise with before your own tests.
Question PaperMay/June examTerm 2Afrikaans
-
Mechanical Technology Grade 12 Term 2 May/June 2018 Question Paper (English)
Free PDF of the Mechanical Technology Grade 12 May/June exam 2018 question paper in English. It tests Term 2 work. Learners looking for the mechanical technology grade 12 june 2018 paper can download it here.
Question PaperMay/June examTerm 2English
-
Mechanical Technology Grade 12 Term 2 May/June 2018 Memo (Afrikaans)
Download the mechanical technology grade 12 june 2018 memo PDF in Afrikaans. It gives the model answers and mark allocation for the May/June exam in Term 2.
MemoMay/June examTerm 2Afrikaans
-
Mechanical Technology Grade 12 Term 2 May/June 2018 Memo (English)
Official memorandum (marking guideline) for Grade 12 Mechanical Technology June 2018, Term 2. Free PDF download in English to check your work after writing the paper.
MemoMay/June examTerm 2English
What is in this paper
10 questions, 200 marks in total. Marks per question are taken from the paper itself.
- Q1 Multiple-Choice Questions Various options are provided as possible answers to the following q ues tions. 20 marks
- Q2 Safety 2.1 Name any TWO pieces of personal safety equipment that you need to wear 10 marks
- Q3 Tools And Equipment 3.1 Tools and equipment are very important to complete different tasks in the 12 marks
- Q4 Materials 4.1 Define the term higher critical temperature in the heating of steel. 13 marks
- Q5 Terminology 5.1 A parallel key must be machined to fit onto 84a mm diameter shaft. 30 marks
- Q6 Joining Methods 6.1 State ONE cause of EACH of the following welding defects: 25 marks
- Q7 Forces 7.1 Four forces of are acting on the same point, as shown in FIGU 7R.1E 30 marks
- Q8 Maintenance 8.1 Why is it important to use oil with a higher viscosity i n a manual 15 marks
- Q9 Systems And Control 9.1 FIGURE 9.1 below shows a gear drive system. Driver gear A on the shaft 25 marks
- Q10 Turbines 10.1 Name TWO types of reaction turbines. 20 marks
Marks per topic
- Terminology30 marks
- Forces30 marks
- Joining Methods25 marks
- Systems And Control25 marks
- Multiple-Choice Questions20 marks
- Turbines20 marks
- Maintenance15 marks
- Materials13 marks
- Tools And Equipment12 marks
- Safety10 marks
Instructions to candidates
- This question paper consists of TEN questions.
- Write your centre number and examination number in the spaces provided on the ANSWER BOOK.
- Read ALL the questions carefully.
- Answer ALL the questions.
- Number the answers correctly according to the numbering system used in this
- Start EACH question on a NEW page.
- Show ALL calculations and units. Round off ALL answers to TWO decim al places.
- Candidates may use non-programmable, scientific calculators and drawing instruments. -2
- Take the value of gravitational force as 10 m/s .
- All dimensions are in millimetres, unless stated otherwise in the question.
- A formula sheet for your use is attached to this question paper.
- Write neatly and legibly.
More Mechanical Technology Grade 12 papers
Same exam, other years
- Mechanical Technology Grade 12 Term 2 May/June 2024
- Mechanical Technology Grade 12 Term 2 May/June 2023
- Mechanical Technology Grade 12 Term 2 May/June 2022
- Mechanical Technology Grade 12 Term 2 May/June 2021
- Mechanical Technology Grade 12 Term 2 May/June 2019
Other 2018 papers
Questions about this paper
How many marks is the Mechanical Technology Grade 12 Term 2 May/June 2018?
The paper is out of 200 marks and you get 3 hours to write it.
Is there a memo for the Mechanical Technology Grade 12 Term 2 May/June 2018?
Yes. The marking memo is on this page as a free PDF download, next to the question paper.
Which topics carry the most marks in this paper?
Terminology (30 marks), forces (30 marks) and joining methods (25 marks).