This page has every Strength of Materials and Structures N5 April paper we have, from 2013 to 2021: 7 question papers and 6 memos in 18 PDFs. Files are in Afrikaans. The newest year is first. Each paper shows the first page of questions, its marks and time, and what the questions cover.
Strength of Materials and Structures N5 April papers by year
Strength of Materials and Structures N5 April 2021 question papers and memos
April 2021
Strength of Materials and Structures N5 April 2021 question paper
100 marks · 3 hours · 6 pages · 7 questions
What is in this paper (7 questions)
Q1
'n Ronde staalstaaf wat aan 'n treklas van 70 kN onderwerp is, word in FIGUUR 1 22 marks
Q2
'n Gewig van 300 kN word deur 'n kort, gewapende kolom ondersteun. FIGUUR 2 toon 25 marks
Q3
Die interne deursnee van 'n silindriese drukhouer is 2,3 m en is beperk tot interne druk 4 marks
Q4
Verwys na die skuifkragdiagram in FIGUUR 3 om die vrae te beantwoord. 13 marks
Q5
FIGUUR 4 verteenwoordig 'n stut met 'n lengte van 12 m wat aan albei ente ingebou 19 marks
Q6
Bereken die maksimum wringkrag wat deur 'n as met 'n deursnee van 63 mm en 'n 10 marks
Q7
7.1 Noem die TWEE hoofmetodes wat gebruik word om staal teen korrosie te 7 marks
Instructions to candidates Answer all the questions. Read all the questions carefully. Number the answers according to the numbering system used in this question paper. Start each question on a new page. Write neatly and legibly. (8060065) -3-
Strength of Materials and Structures N5 April 2019 question papers and memos
April 2019
Strength of Materials and Structures N5 April 2019 question paper
100 marks · 3 hours · 7 pages · 7 questions
The memo for this paper is not available yet.
What is in this paper (7 questions)
Q1
Die staalstaaf in FIGUUR 1 hier onder bestaan uit twee dele: die een deel is 90 mm 15 marks
Q2
2.1 Die saamgestelde staaf in FIGUUR 2 hier onder word in 'n masjien se 26 marks
Q3
'n Staalketeldrom ('steel boiler drum') met 'n wand wat 18 mm dik is, is ontwerp om 10 marks
Q4
FIGUUR 3 hier onder toon 'n opgeboude balk wat bestaan uit 'n gleuf ('channel') en 'n 20 marks
Q5
'n Soliede as van 1,55 m word as 'n trekkerdryfas ('prop shaft') gebruik. Die skag draai 16 marks
Q6
Dui aan van die volgende stellings rakende meganiese toetsing WAAR of ONWAAR is. 5 marks
Q7
FIGUUR 4 hier onder toon die raamwerk van 'n enkelvoudig gesteunde kantelbalk 8 marks
Instructions to candidates Answer ALL the questions. Read ALL the questions carefully. Number the answers according to the numbering system used in this question paper. Sketches must be large, neat and fully labelled. Show ALL the calculations where calculations are required. Write neatly and legibly. (8060065) -3-
Strength of Materials and Structures N5 April 2018 question papers and memos
April 2018
Strength of Materials and Structures N5 April 2018 question paper
100 marks · 3 hours · 6 pages · 5 questions
What is in this paper (5 questions)
Q1
'n Trektoets word op 'n staalstaaf uitgevoer. Die toetsstuk se deursnee is 20 mm en is 20 marks
Q2
'n Silindriese drukhouer word onder 'n drukking van 1,2 MPa geplaas. Die drukhouer is 12 marks
Q3
'n Saamgestelde as bestaan uit 'n soliede staalstaaf wat binne-in 'n brons silinder pas. 13 marks
Q4
Bestudeer die eenvoudig ondersteunde balk in FIGUUR 4 hier onder en beantwoord 30 marks
Q5
FIGUUR 5 beskik oor die volgende eienskappe: 25 marks
Instructions to candidates Answer ALL the questions. Read ALL the questions carefully. Number the answers according to the numbering system used in this question paper. Write neatly and legibly. (8060065) -3- T1650(E)(A13)T
Strength of Materials and Structures N5 April 2016 question papers and memos
April 2016
Strength of Materials and Structures N5 April 2016 question paper
100 marks · 3 hours · 7 pages · 9 questions
What is in this paper (9 questions)
Q1
Sketch neatly a typical stress-strain graph for mild-steel in good proportions and 10 marks
Q2
Figure 1 FIGURE 1, shows a rod subjected to a tensile load of 125 kN. The maximum tensile 16 marks
Q3
Figure 2 A compound shaft ABC is as shown in FIGURE 2 and it is clamped at A. Portion AB is 11 marks
Q4
A steel bar of 28 mm in diameter and 1.2 m long absorbs 68J of energy at its limit of 12 marks
Q5
A compound bar consists of a solid steel rod with a cross-sectional area of 2.5 cm2 and 15 marks
Q6
A steel pipe is used to convey oil between two points. The pipe can be assumed to be 10 marks
Q7
A thin cylindrical pipe with a diameter of 300 mm and a thickness of 6 mm is closed at 6 marks
Q8
A straight bar of steel 1.5 m long and 30 mm by 7 mm in section is mounted in a 8 marks
Q9
Graphically determine the magnitude and nature of forces in each member of the 12 marks
Instructions to candidates Answer ALL the questions. Read ALL the questions carefully. Number the answers according to the numbering system used in this question paper. Write neatly and legibly. (8060065) -3- T1560(E)(A6)T
Strength of Materials and Structures N5 April 2015 question papers and memos
April 2015
Strength of Materials and Structures N5 April 2015 question paper
Strength of Materials and Structures N5 April 2014 question papers and memos
April 2014
Strength of Materials and Structures N5 April 2014 question paper
Strength of Materials and Structures N5 April 2013 question papers and memos
April 2013
Strength of Materials and Structures N5 April 2013 question paper
No papers match. Clear the filters
Questions about these papers
Which years of Strength of Materials and Structures N5 April papers are on this page? Papers from 2021, 2019, 2018, 2016, 2015, 2014, 2013. The newest year is at the top.
How many marks is the Strength of Materials and Structures N5 April paper? The paper is usually out of 100 marks and you get 3 hours to write it.
Are the memos included? Yes. 6 of the 7 papers on this page have their marking memo next to the question paper.
