Civil Technology Grade 12 Term 2 June Past Papers and Memos

1. Q1 Wbgv, Materiale, Gereedskap, Toerusting en Hegtin G (Generies)1.1 Kies die korrekte woord(e) uit dié wat tussen hakies gegee word. Skryf slegs 20 marks
2. Q2 Grafika As Kommunikasiemiddel (Generies)FIGUUR A en FIGUUR B op die volgende bladsy toon tekeninge wat op 'bouplann 40 marks
3. Q3 3.1 Hoekom is dit belangrik om openinge op konstruksieterreine te beveilig? (2) 30 marks
4. Q4 Koue- en Warmwatertoevoer, Gereedskap, Toerusting en Materiaal (Spesifiek)4.1 Kies 'n beskrywing uit KOLOM B wat bydie item in KOLOM A pas. Skry f 40 marks
5. Q5 Grafika As Kommunikasiemiddel, Dakwerk en Stormwater (Spesifiek)5.1 Verskeie opsies word as moontlike antwoorde op die volgende vrae gegee. 30 marks
6. Q6 Riolering, Sanitêre Toebehore en Hegting (Spesifiek)6.1 Voltooi die volgende sinne deur die woord/term in die lys hieronder te gebruik. 40 marks

Instructions to candidates

1. Hierdie vraestel bestaan uit SES vrae.
2. Beantwoord AL die vrae.
3. Lees AL die vrae noukeurig deur.
4. Beantwoord elke vraag as 'n geheel. MOENIE onderafdelings van vrae skei NIE.
5. Nommer die antwoorde korrek volgens die nommeringstelsel wat in hierdie vraestel gebruik is.
6. Begin die antwoord op ELKE vraag op 'n NUWE bladsy.
7. MOENIE in die kantlyne van die ANTWOORDEBOEK skryf NIE.
8. Jy mag sketse gebruik om jou antwoorde te illustreer.
9. Skryf ALLE berekeninge en antwoorde in die ANTWOORDEBOEK of op die aangehegte ANTWOORDBLAAIE.
10. Gebruik die puntetoekenning as 'n riglyn vir die lengte van jou antwoorde.
11. Maak tekeninge en sketse met potlood, volledig gemaatskryf en netjies met beskrywende opskrifte en aantekeninge afgerond, in ooreenstemming met die SANS/SABS se Gebruikskode vir Boutekenepraktyk.
12. Vir die doel van hierdie vraestel moet die grootte vteean 'n asn s 220 mm x 110 mm x 75 mm geneem word.
13. Gebruik jou eie oordeel waar afmetings en/of inligting ontbreek.
14. Beantwoord VRAAG 2, 3.6, 5.5 en 6.5 op die aangehegte ANTWOORDBLAAIE en gebruik tekeninstrumente, waar nodig.

1. Q1 Ohsa, Materials, Tools, Equipment Andjoin Ing (Generic)1.1 Choose the correct word(s) from those given in brackets. Write only the word(s) 20 marks
2. Q2 Graphics As Means of Communication (Generic)FIGURE A and FIGURE B on the next page show drawings that appear on a buildi ng 40 marks
3. Q3 Roofs, Staircases and Joining (Specific)3.1 FIGURE 3.1 below shows a roof construction where clay roof tiles are used. 30 marks
4. Q4 4.1 Give ONE word/term for each of the following descriptionsW. rite only the 40 marks
5. Q5 5.1 Choose a description from COLUMN B that matchesth e item in COLUMN A. 30 marks
6. Q6 Reinforcement in Concrete, Foundations, Concrete Floors and Quantities (Specific)6.1 Various options are given as possible answers to the following questions . 40 marks

Instructions to candidates

1. This question paper consists of SIX questions.
2. Answer ALL the questions.
3. Read ALL the questions carefully.
4. Answer each question as a whole. Do NOT separate subsections of questions.
5. Number the answers correctly according to the numbering system used in this question paper.
6. Start the answer to EACH question on a NEW page.
7. Do NOT write in the margins of the ANSWER BOOK.
8. You may use sketches to illustrate your answers.
9. Write ALL calculations and answers in the ANSWER BOOK or on the attached ANSWER SHEETS.
10. Use the mark allocation as a guide to the length of your answers.
11. Make drawings and sketches in pencil, fully dimensioned and neatly finished off with descriptive ttlei s and notes to conform to theS ANS/SABS Code of Practice for Building Drawings.
12. For the purpose of this question paper, the size of a brick should be taken as 220 mm x 110 mm x 75 mm.
13. Use your own discretion where dimensions and/or details have been omitted.
14. Answer QUESTIONS 2, 3, .74.9, 5.4 and 6.6 on the attached ANSWER SHEETS using drawing instruments, where necessary.

1. Q1 Ohsa, Materials, Tools, Equipment and Join in G (Generic)1.1 Choose the correct word(s) from those given in brackets. Write only the word(s) 20 marks
2. Q2 Graphics As Means of Communication (Generic)FIGURE A and FIGURE B on the next page show drawintghats appear on a building 40 marks
3. Q3 3.1 FIGURE 3.1 below shows the front elevation of a free-standing cupboard with 30 marks
4. Q4 Roofs, Ceilings, Tools, Equipment and Materials (Specific)4.1 Various options are provided as possible answers to the following questions . 40 marks
5. Q5 Centering, Formwork, Shoring and Graphics As Means of Communication (Specific)5.1 FIGURE 5.1 below shows a part of a dead shore. 30 marks
6. Q6 Suspended Floors, Staircases, Ironmongery, Doors and Joining (Specific)6.1 Choose a description from COLUMN B that matches the item in COLUMN A. 40 marks

Instructions to candidates

1. This question paper consists of SIX questions.
2. Answer ALL the questions.
3. Read ALL the questions carefully.
4. Answer each question as a whole. Do NOT separate subsections of questions.
5. Number the answers correctly according to the numbering system used in this question paper.
6. Start the answer to EACH question on a NEW page.
7. Do NOT write in the margins of the ANSWER BOOK.
8. You may use sketches to illustrate your answers.
9. Write ALL calculations and answers in the ANSWER BOOK or on the attached ANSWER SHEETS.
10. Use the mark allocation as a guide to the length of your answers.
11. Make drawings and sketches in pencil, fully dimensioned and neatly finished off with descriptive titles and notes to conform to the SANS/SABS Cod e of Practice for Building Drawings.
12. For the purpose of this question paper, the size of a brick should be taken as 220 mm x 110 mm x 75 mm.
13. Use your own discretion where dimensions and/or details have been omitted.
14. Answer QUESTIONS 2, 3.1, 3.2, 3.3, 3.4, 4.6, 5.5, 5.6, 6.5 and 6.6 on the attached ANSWER SHEETS using drawing instruments, where necessary.

1. Q1 Ohsa, Materials, Tools, Equipment and Join in G (Generic) 20 marks
2. Q2 Graphics As Means of Communication (Generic)
3. Q3 Construction Associated with Civil Services, Ohsa and Quantities (Specific) 30 marks
4. Q4 Cold and Hot-Water Supply, Tools, Equipment and Materials (Specific) 40 marks
5. Q5 Graphics As Means of Communication, Roof Work and Storm Water (Specific) 30 marks
6. Q6 Sewerage, Sanitary Fittings and Joining (Specific) 40 marks

Instructions to candidates

1. Markers should: • Familiarise themselves with the question and answer before evaluating the responses of candidates. • Always interpret the responses of the candidates within the context of the question. • Consider any relevant and acceptable answer durmingar
2. If a candidate is required to explain e.g., a process in 4 steps, only the first 4 responses should be considered.
3. However, if for example candidate is required to explain or describe a process, we need to consider that that candidates may write a long description, not necessarily elwl organised. In this case the marker needs to evaluate the complete statement to judge if
4. For calculations: • A mark is only awarded if the correct unit is written next to the answer. If the question states that the answer must be in a specific unit, a mark will ONLY be awarded if the answer has the correct unit as indicated in the question. • Mark
5. When marking drawings: • The member for which the mark should be awarded should be drawn correctly in the correct position to receive a mark. • A member incorrectly drawn but wrongfully repeated in another position will be awarded the mark for the repeated inc
6. Incorrect numbering of questions: • If a candidate numbered an incorrecly,t but the answer is in the correct position according to the sequence of the questions in the question paper, circle then the incorrect numbering and mark the response. • If questions we
7. Duplication of responses and questions answered in the correct place: • If a question is answered twice, mark the first response. • If a question should be answered on an nswera sheet and the candidate answered it on both the answer sheet and in the answer boo

1. Q1 Ohsa, Materials, Tools, Equipment and Join in G (Generic) 20 marks
2. Q2 Graphics As Means of Communication (Generic)
3. Q3 Roofs, Staircases and Joining (Specific) 30 marks
4. Q4 Excavations, Formwork, Tools, Equipment and Materials (Specific) 40 marks
5. Q5 Plaster and Screed, Brickwork Angd Raphics As Means of Communication (Specific) 30 marks
6. Q6 Reinforcement in Concrete, Foundations, Concret E Floors and Quantities (Specific) 40 marks

Instructions to candidates

1. Markers should: • Familiarise themselves with the question and answer before evaluating the responses of candidates. • Always interpret the responses of the candidates within the context of the question. • Consider any relevant and acceptable answer during pre
2. If a candidate is required to explain e.g., a process in 4 steps, only the first 4 responses should be considered.
3. However, if for example candidate is required to explain or describe a process, we need to consider that that candidates may write a long description, not necessarily well organised. In tis chase the marker needs to evaluate the complete statement to judge if
4. For calculations: • A mark is only awarded if the correct unit is written next to the answer. If the question states that the answer must be in a specific unit, a mark will ONLY be awarded if the answer has the correct unit as indicated in the question. • Mark
5. When marking drawings: • The member for which the mark should be awarded should be drawn correctly in the correct position to receive a mark. • A member incorrectly drawn but wrongfully repeated in another position will be awarded the mark for the repeated inc
6. Incorrect numbering of questions: • If a candidate numbered an incorrectly, but tanshe wer is in the correct position according to the sequence of the questions in the question paper, circle then the incorrect numbering and mark the response. • If questions we
7. Duplication of responses and questions answered in the correct place: • If a question is answered twice, mark the first response. • If a question should be answered on an answer sheetand t he candidate answered it on both the answer sheet and in the answer boo

1. Q1 Ohsa, Materials, Tools, Equipment and Joinin G (Generic) 20 marks
2. Q2 Graphics As Means of Communication (Generic)
3. Q3 Question 3 30 marks
4. Q4 Roofs, Ceilings, Toolse, Quipment and Materials (Specific) 40 marks
5. Q5 Question 5 30 marks
6. Q6 S Uspended Floors, Staircases, Ironmongery, Doors and Joining (Specific) 40 marks

Instructions to candidates

1. Markers should: • Familiarise themselves with the question and answer before evaluating the responses of candidates. • Always interpret the responses of the candidates within the context of the question. • Consider any relevant and acceptable answer duringma p
2. If a candidate is required to explain e.g., a process in 4 steps, only the first 4 responses should be considered.
3. However, if for example candidate is required to explain or describe a process, we need to consider that that candidates may write a long description, not necessarily well organised. In this case the marker needs to evaluate the complete statement to judge if
4. For calculations: • A mark is only awarded if the correct unit is written next to the answer. If the question states that the answer must be in a specific unit, a mark will ONLY be awarded if the answer has the correct unit as indicated in the question. • Mark
5. When marking drawings: • The member for which the mark should be awarded should be drawn correctly in the correct position to receive a mark. • A member incorrectly drawn but wrongfully repeated in another position will be awarded the mark for the repeated inc
6. Incorrect numbering of questions: • If a candidate numbered an incorrectly, but the answer is in the correct position according to the sequence of the questions in the question paper, circle then the incorrect numbering and mark the response. • If questions we
7. Duplication of responses and questions answered in the correct place: • If a question is answered twice, mark the first response. • If a question should be answered on an answer sheet and the candidate answered it on both the answer sheet and in the answer boo

1. Q1 Ohsa, Materials, Tools, Equipment and Joining (Generic) 20 marks
2. Q2 Graphics As Means of Communication (Generic)
3. Q3 Construction Associated with Civil Services, Ohsa and Quantities (Specific) 30 marks
4. Q4 Cold and Hot-Water Supply, Tools, Equipment and Materials (Specific) 40 marks
5. Q5 Graphics As Means of Communication, Roof Work and Storm Water (Specific) 30 marks
6. Q6 Sewerage, Sanitary Fittings and Joining (Specific) 40 marks

Instructions to candidates

1. Markers should: • Familiarise themselves with the question and answer before evaluating the responses of candidates. • Always interpret the responses of the candidates within the context of the question. • Consider any relevant and acceptable answer during pre
2. If a candidate is required to explain e.g., a process in 4 steps, only the first 4 responses should be considered.
3. However, if for example candidate is required to explain or describe a process, we need to consider that that candidates may write a long description, not necessarily well organised. In this case, the marker needs to evaluate the complete statement to judge if
4. For calculations: • A mark is only awarded if the correct unit is written next to the answer. If the question states that the answer must be in a specific unit, a mark will ONLY be awarded if the answer has the correct unit as indicated in the question. • Mark
5. When marking drawings: • The member for which the mark should be awarded should be drawn correctly in the correct position to receive a mark. • A member incorrectly drawn but wrongfully repeated in another position will be awarded the mark for the repeated inc
6. Incorrect numbering of questions: • If a candidate numbered an incorrectly, but the answer is in the correct position according to the sequence of the questions in the question paper, circle then the incorrect numbering and mark the response. • If questions we
7. Duplication of responses and questions answered in the correct place: • If a question is answered twice, mark the first response. • If a question should be answered on an answer sheet and the candidate answered it on both the answer sheet and in the answer boo

1. Q1 Wbgv, Materiale, Gereedskap, Toerusting en Hegting (Generies) 20 marks
2. Q2 Question 2
3. Q3 Dakke, Trappe en Verbinding (Spesifiek) 30 marks
4. Q4 Uitgrawings, Bekisting, Gereedskap, Toerusting en Materiale (Spesifiek) 40 marks
5. Q5 Pleister en Vlaklae, Steenwerk en Grafika As Kommunikasiemiddel (Spesifiek) 30 marks
6. Q6 Wapening in Beton, Fondasies, Beton Vloere en Hoeveelhede (Spesifiek) 40 marks

1. Q1 Ohsa, Materials, Tools, Equipment and Joining (Generic) 20 marks
2. Q2 Graphics As Means of Communication (Generic)
3. Q3 Cupboards, Casements 30 marks
4. Q4 Roofs, Ceilings, Tools, Equipment and Materials (Specific) 40 marks
5. Q5 Centering, Formwork, Shoring and Graphics As Means of Communication (Specific) 30 marks
6. Q6 Suspended Floors, Staircases, Iron Mongery, Doors and Joining (Specific) 40 marks

Instructions to candidates

1. Markers should: • Familiarise themselves with the question and answer before evaluating the responses of candidates. • Always interpret the responses of the candidates within the context of the question. • Consider any relevant and acceptable answer during pre
2. If a candidate is required to explain e.g., a process in 4 steps, only the first 4 responses should be considered.
3. However, if for example candidate is required to explain or describe a process, we need to consider that that candidates may write a long description, not necessarily well organised. In this case the marker needs to evaluate the complete statement to judge if
4. For calculations: • A mark is only awarded if the correct unit is written next to the answer. If the question states that the answer must be in a specific unit, a mark will ONLY be awarded if the answer has the correct unit as indicated in the question. • Mark
5. When marking drawings: • The member for which the mark should be awarded should be drawn correctly in the correct position to receive a mark. • A member incorrectly drawn but wrongfully repeated in another position will be awarded the mark for the repeated inc
6. Incorrect numbering of questions: • If a candidate numbered an incorrectly, but the answer is in the correct position according to the sequence of the questions in the question paper, circle then the incorrect numbering and mark the response. • If questions we
7. Duplication of responses and questions answered in the correct place: • If a question is answered twice, mark the first response. • If a question should be answered on an answer sheet and the candidate answered it on both the answer sheet and in the answer boo

1. Q1 Ohsa, Materials, Tools, Equipment and Joining (Generic) 20 marks
2. Q2 Graphics As Means of Communication (Generic)
3. Q3 Construction Associated with Civil Services, Ohsa and Quantities (Specific) 30 marks
4. Q4 Cold- and Hot-Water Supply, Tools, Equipment and Materials (Specific) 40 marks
5. Q5 Graphics As Means of Communication, Roof Work and Stormwater (Specific) 30 marks
6. Q6 Sewerage, Sanitary Fittings and Joining (Specific) 40 marks

Instructions to candidates

1. Markers should:  Familiarise themselves with the question and answer before evaluating the responses of candidates.  Always interpret the responses of the candidates within the context of the question.  Consider any relevant and acceptable answer during pre
2. For calculations:  A mark is only awarded if the correct unit is written next to the answer.  If TWO marks are awarded ONE mark is awarded for the answer and ONE mark for the correct unit.  Where the candidate made a principle error, e.g. added instead of m
3. When marking drawings:  The member for which the mark should be awarded should be drawn correctly in the correct position to receive a mark.  A member incorrectly drawn but wrongfully repeated in another position will be awarded the mark for the repeated inc

1. Q1 Ohsa, Materials, Tools, Equipment and Joining (Generic) 20 marks
2. Q2 Graphics As Means of Communication (Generic)
3. Q3 Roofs, Staircases and Joining (Specific) 30 marks
4. Q4 Excavations, Formwork, Tools, Equipment and Materials (Specific) 40 marks
5. Q5 Plaster and Screed, Brickwork and Graphics As Means of Communication (Specific) 30 marks
6. Q6 Reinforcement in Concrete, Foundations, Concrete Floors and Quantities (Specific) 40 marks

Instructions to candidates

1. Markers should:  Familiarise themselves with the question and answer before evaluating the responses of candidates.  Always interpret the responses of the candidates within the context of the question.  Consider any relevant and acceptable answer during pre
2. For calculations:  A mark is only awarded if the correct unit is written next to the answer.  If TWO marks are awarded ONE mark is awarded for the answer and ONE mark for the correct unit.  Where the candidate made a principal error, e.g. added instead of m
3. When marking drawings:  The member for which the mark should be awarded should be drawn correctly in the correct position to receive a mark.  A member incorrectly drawn but wrongfully repeated in another position will be awarded the mark for the repeated inc

1. Q1 Ohsa, Materials, Tools, Equipment and Joining (Generic) 20 marks
2. Q2 Graphics As Means of Communication (Generic)
3. Q3 Cupboards, Casements, Wall-Panelling and Quantities (Specific) 30 marks
4. Q4 Roofs, Ceilings, Tools, Equipment and Materials (Specific) 40 marks
5. Q5 Centering, Formwork, Shoring and Graphics As Means of Communication (Specific) 30 marks
6. Q6 Suspended Floors, Staircases, Ironmongery, Doors and Joining (Specific) 40 marks

Instructions to candidates

1. Markers should:  Familiarise themselves with the question and answer before evaluating the responses of candidates.  Always interpret the responses of the candidates within the context of the question.  Consider any relevant and acceptable answer during pre
2. For calculations:  A mark is only awarded if the correct unit is written next to the answer.  If TWO marks are awarded ONE mark is awarded for the answer and ONE mark for the correct unit.  Where the candidate made a principle error, e.g. added instead of m
3. When marking drawings:  The member for which the mark should be awarded should be drawn correctly in the correct position to receive a mark.  A member incorrectly drawn but wrongfully repeated in another position will be awarded the mark for the repeated inc

1. Q1 Ohsa, Safety, Materials, Tools, Equipment and Joining (Generic)1.1 Give ONE word/term for each of the following descriptions by choosing a 20 marks
2. Q2 Graphics As Means of Communication (Generic)FIGURE 2 on the next page shows a drawing that appears on a building plan. Analyse 40 marks
3. Q3 Construction Associated with Civil Services, Ohsa and Quantities (Specific)3.1 FIGURE 3.1 below is a drawing of a temporary excavation exposing the 30 marks
4. Q4 Hot- and Cold-Water Supply, Tools, Equipment and Materials (Specific)4.1 FIGURE 4.1 below is a drawing of a device used in cold-water systems. 40 marks
5. Q5 Graphics As Means of Communication, Roof Work and Storm Water (Specific)5.1 Draw a neat freehand drawing in your ANSWER BOOK to show the 30 marks
6. Q6 Sewerage, Sanitary Fittings and Joining (Specific)6.1 Various options are given as possible answers to the following questions. 40 marks

Instructions to candidates

1. This question paper consists of SIX questions.
2. Answer ALL the questions.
3. Read all the questions carefully.
4. Answer each question as a whole. Do NOT separate subsections of questions.
5. Number the answers correctly according to the numbering system used in this question paper.
6. Start the answer to EACH question on a NEW page.
7. Do NOT write in the margins of the ANSWER BOOK.
8. You may use sketches to illustrate your answers.
9. Write ALL calculations and answers in the ANSWER BOOK or on the attached ANSWER SHEETS. The SI unit for answers must be indicated next to the answer.
10. Use the mark allocation as a guide to the length of your answers.
11. Make drawings and sketches in pencil, fully dimensioned and neatly finished off with descriptive titles and notes to conform to the SANS/SABS Code of Practice for Building Drawings.
12. For the purpose of this question paper, the size of a brick should be taken as 220 mm x 110 mm x 75 mm.
13. Use your own discretion where dimensions and/or details have been omitted.
14. Answer QUESTIONS 2, 3.10, 5.4 and 6.10 on the attached ANSWER SHEETS using drawing instruments, where necessary.

1. Q1 Ohsa, Safety, Materials, Tools, Equipment and Joining (Generic)1.1 Give ONE word/term for each of the following descriptions by choosing a 20 marks
2. Q2 Graphics As Means of Communication (Generic)FIGURE 2 on the next page shows a drawing that appears on a building plan. Analyse 40 marks
3. Q3 Roofs, Staircases and Joining (Specific)3.1 Complete the following sentence by choosing the missing word/term
4. Q4 Excavations, Formwork, Tools, Equipment and Materials (Specific)4.1 Choose a description from COLUMN B that matches an item in COLUMN A. 40 marks
5. Q5 Plaster and Screed, Brickwork and Graphics As Means of Communication (Specific)5.1 Name the application applied to a wall surface to achieve a high quality and 30 marks
6. Q6 Reinforcement in Concrete, Foundations, Concrete Floors and Quantities (Specific)6.1 Various options are given as possible answers to the following questions. 40 marks

Instructions to candidates

1. This question paper consists of SIX questions.
2. Answer ALL the questions.
3. Read all the questions carefully.
4. Answer each question as a whole. Do NOT separate subsections of questions.
5. Number the answers correctly according to the numbering system used in this question paper.
6. Start the answer to EACH question on a NEW page.
7. Do NOT write in the margins of the ANSWER BOOK.
8. You may use sketches to illustrate your answers.
9. Write ALL calculations and answers in the ANSWER BOOK or on the attached ANSWER SHEETS. The SI unit for answers must be indicated next to the answer.
10. Use the mark allocation as a guide to the length of your answers.
11. Make drawings and sketches in pencil, fully dimensioned and neatly finished off with descriptive titles and notes to conform to the SANS/SABS Code of Practice for Building Drawings.
12. For the purpose of this question paper, the size of a brick should be taken as 220 mm x 110 mm x 75 mm.
13. Use your own discretion where dimensions and/or details have been omitted.
14. Answer QUESTIONS 2, 3.8, 5.9, 5.10, 5.11, 6.6 and 6.7 on the attached ANSWER SHEETS using drawing instruments, where necessary.

1. Q1 Ohsa, Safety, Materials, Tools, Equipment and Joining (Generic)1.1 Give ONE word/term for each of the following descriptions by choosing a 20 marks
2. Q2 Graphics As Means of Communication (Generic)FIGURE 2 on the next page shows a drawing that appears on a building plan. Analyse 40 marks
3. Q3 Cupboards,Casements, Wall-Panelling and Quantities (Specific)3.1 FIGURE 3.1 below shows the inside of a built-in cupboard without doors. 30 marks
4. Q4 Roofs, Ceilings, Tools, Equipment and Materials (Specific)4.1 FIGURE 4.1 below shows four machines. Study the pictures and answer the 40 marks
5. Q5 Centering, Formwork, Shoring and Graphics As Means of Communication (Specific)5.1 Draw, in good proportion, in your ANSWER BOOK a side view of the ribs and 30 marks
6. Q6 Suspended Floors, Staircases, Ironmongery, Doors and Joining (Specific)6.1 Various options are given as possible answers to the following questions. 40 marks

Instructions to candidates

1. This question paper consists of SIX questions.
2. Answer ALL the questions.
3. Read all the questions carefully.
4. Answer each question as a whole. Do NOT separate subsections of questions.
5. Number the answers correctly according to the numbering system used in this question paper.
6. Start the answer to EACH question on a NEW page.
7. Do NOT write in the margins of the ANSWER BOOK.
8. You may use sketches to illustrate your answers.
9. Write ALL calculations and answers in the ANSWER BOOK or on the attached ANSWER SHEETS. The SI unit for answers must be indicated next to the answer.
10. Use the mark allocation as a guide to the length of your answers.
11. Make drawings and sketches in pencil, fully dimensioned and neatly finished off with descriptive titles and notes to conform to the SANS/SABS Code of Practice for Building Drawings.
12. For the purpose of this question paper, the size of a brick should be taken as 220 mm x 110 mm x 75 mm.
13. Use your own discretion where dimensions and/or details have been omitted.
14. Answer QUESTIONS 2, 3.6, 4.8, 5.2, 5.4, 5.5 and 6.9.2 on the attached ANSWER SHEETS using drawing instruments, where necessary.

1. Q1 Wbgv, Materiaal, Veiligheid, Gereedskap, Toerusting en Hegting (Generies)1.1 Kies 'n beskrywing uit KOLOM B wat by 'n item in KOLOM A pas. Skryf slegs 20 marks
2. Q2 Grafika As Kommunikasiemiddel (Generies)FIGUUR 2 op die volgende bladsy toon 'n aansig en 'n grondvloerplan wat op 'n 40 marks
3. Q3 3.1 FIGUUR 3.1 hieronder is 'n illustrasie van 'n mangat. Bestudeer die illustrasie 30 marks
4. Q4 Warm- en Kouewatertoevoer, Gereedskap, Toerusting en Materiaal (Spesifiek)4.1 FIGUUR 4.1 hieronder toon 'n prent van 'n waterverwarmingstelsel wat in die 40 marks
5. Q5 Grafika As Kommunikasiemiddel, Dakwerk en Stormwater (Spesifiek)5.1 Gee EEN woord/term vir elk van die volgende beskrywings deur 'n 30 marks
6. Q6 Riolering, Sanitêre Toebehore en Hegting (Spesifiek)6.1 Verskeie opsies word as moontlike antwoorde op die volgende vrae gegee. 40 marks

1. Q1 Wbgv, Materiaal, Veiligheid, Gereedskap, Toerusting en Hegting (Generies)1.1 Kies 'n beskrywing uit KOLOM B wat by 'n item in KOLOM A pas. Skryf slegs 20 marks
2. Q2 Grafika As Kommunikasiemiddel (Generies)FIGUUR 2 op die volgende bladsy toon 'n aansig en 'n grondvloerplan wat op 'n 40 marks
3. Q3 Dakke, Trappe en Verbinding/Hegting (Spesifiek)3.1 Gee die minimum dakhelling wanneer betonteëls as dakbedekking gebruik 30 marks
4. Q4 Uitgrawings, Bekisting, Gereedskap en Toerusting en Materiaal (Spesifiek)4.1 Noem TWEE eienskappe van ELK van die volgende metale: 40 marks
5. Q5 5.1 Kies 'n beskrywing uit KOLOM B wat by 'n item in KOLOM A pas. Skryf 30 marks
6. Q6 Wapening in Beton, Fondasies, Betonvloere en Hoeveelhede (Spesifiek)6.1 Verskeie opsies word as moontlike antwoorde op die volgende vrae gegee. 40 marks

1. Q1 Ohsa, Safety, Materials, Tools, Equipment and Joining (Generic)1.1 Choose a description from COLUMN B that matches an item in COLUMN A. 20 marks
2. Q2 Graphics As Means of Communication (Generic)FIGURE 2 on the next page shows an elevation and a ground floor plan that appear on 40 marks
3. Q3 Casements, Cupboards, Wall-Panelling and Quantities (Specific)3.1 Name the part of a casement that separates two window panes so that they 30 marks
4. Q4 Roofs, Ceilings, Tools and Equipment, and Materials (Specific)4.1 Choose a term from COLUMN B that matches a roof in COLUMN A. Write 40 marks
5. Q5 Centring, Formwork, Shoring and Graphics As Means of Communication (Specific)5.1 Draw a neat two-dimensional sketch to show the open laggings, rib and 30 marks
6. Q6 Suspended Floors, Staircases, Ironmongery, Doors and Joining (Specific)6.1 Various options are given as possible answers to the following questions. 40 marks

Instructions to candidates

1. This question paper consists of SIX questions.
2. Answer ALL the questions.
3. Answer each question as a whole. Do NOT separate subsections of questions.
4. Start the answer to EACH question on a NEW page.
5. Do NOT write in the margins of the ANSWER BOOK.
6. You may use sketches to illustrate your answers.
7. Write ALL calculations and answers in the ANSWER BOOK or on the attached ANSWER SHEETS.
8. Use the mark allocation as a guide to the length of your answers.
9. Make drawings and sketches in pencil, fully dimensioned and neatly finished off with descriptive titles and notes to conform to the SANS/SABS Code of Practice for Building Drawings.
10. For the purpose of this question paper, the size of a brick should be taken as 220 mm x 110 mm x 75 mm.
11. Use your own discretion where dimensions and/or details have been omitted.
12. Answer QUESTIONS 2, 3.3, 3.4, 3.5, 4.2, 5.6, 6.2, 6.5 and 6.6 on the attached ANSWER SHEETS using drawing instruments where necessary.
13. Write your CENTRE NUMBER and EXAMINATION NUMBER on every ANSWER SHEET and hand them in with your ANSWER BOOK, whether you have used them or not.
14. Drawings in the question paper are NOT to scale due to electronic transfer.

1. Q1 Construction, Safety and Materials1.1 Study FIGURE 1.1 below that shows a worker drilling on ac onstruction site 30 marks
2. Q2 Advanced Construction and Equipment2.1 FIGURE 2.1 belowis a sketch of a precast concrete pile driven int o t he 40 marks
3. Q3 Civil Services3.1 Choose a description from COLUMN B that matches an item in COLUMN A. 30 marks
4. Q4 Quantities, Materials and Joining4.1 Various options are given as possible answers to the following questions . 30 marks
5. Q5 Applied Mechanics5.1 FIGURE 5.1 shows a shaped lamina. All dimensions are in millimetres. 30 marks
6. Q6 Graphics and Communication6.1 FIGURE 6.1 below illustrates a detailed sectional view of the foot of a king 40 marks

Instructions to candidates

1. This question paper consists of SIX questions.
2. Answer ALL the questions.
3. Answer each question as a w Do Nhole.OT separate subsections of questions.
4. Start the answer to EACH question on a NEW page.
5. Do NOT write in the margins of the ANSWER BOOK.
6. You may use sketches to illustrate your answers.
7. Write ALL calculations and answers in the ANSWER BOOe K or on th attached ANSWER SHEETS.
8. Use the mark allocation as a guide to the length of your answers.
9. Make drawings and sketches in pencil, fully dimensioned and neatly finished off with descriptive titles and notes to conform to the SANS/SABS Code of Practice for Building Drawings.
10. For the purpose of this question paper, the size of a brick should be taken as 220 mm x 110 mm x 75 mm.
11. Use your own discretion where dimensions and/or details have been omitted.
12. Answer QUESTIONS 2.,7 3.5, 4.3, 5.2, 5.3, 6.1 and 6.on2 the attached ANSWER SHEETS using drawing instruments, where necessary.
13. Write your CENTRE NUMBER and EXAMINATION NUMBER on every ANSWER SHEET and hand them in with your ANSWER BOOK, whether you have used them or not.
14. Drawings in the question paper are NOT to scale due to electronic transfer.